
Chimney Rebuild in Bloomfield, NJ
When the brick is loose, leaning or past patching, the chimney comes down to sound masonry and goes back up right.
Repairs can only go so far. Once the bricks at the top of a chimney are loose enough to lift by hand, or the stack has started to lean away from the house, sealing and repointing will not make it safe. A chimney rebuild in Bloomfield, NJ means taking the damaged masonry down to brick that is still solid and building it back with new materials, a proper crown and new flashing.
Most chimneys never get to this point. If the damage is limited to mortar joints or a few flaking bricks, masonry repair is the better answer, and a cracked crown alone is a chimney repair. We will tell you which one your chimney needs, and the estimate is free.
Signs a chimney needs rebuilding
- The chimney leans, or there is a gap opening between the chimney and the side of the house.
- Bricks near the top are loose, missing or move when pushed.
- Mortar has washed out so deeply that whole courses are sitting on sand.
- Large areas of spalled brick, more than a few pieces can fix.
- Cracks that run through several courses of brick, not just along the joints.
How a chimney gets this far
Usually it is years of water. A crown that cracked long ago, a missing cap or open joints let rain into the core of the chimney. Each winter that water freezes, and the masonry loosens from the inside out. The part above the roof goes first because it is exposed on every side.
A lean has other causes too, such as a footing that has settled or a chimney that was never tied properly to the house.
How we decide how much comes down
We check the brick course by course from the top, looking for the point where the mortar is hard and the bricks are tight again. That is where a rebuild stops. We also look at the chimney in the attic and at the base, and check whether the flue liner can stay. When the condition inside is unclear, a Level 2 inspection with a camera answers it before any brick is removed.

Partial chimney rebuild
A partial rebuild is the most common kind. The chimney is taken down from the top to a point at or below the roof line where the masonry is sound, then relaid with new brick and mortar. The flue tiles in that section are replaced or a new liner is fitted. The job finishes with a new crown and new flashing, since both have to be redone once the brick at the roof changes.
Full chimney rebuild
A full rebuild takes the chimney down to the foundation or the firebox and builds it again. It is needed when damage runs the whole height of the stack, when the footing has failed, or after a serious chimney fire has cracked the structure. It is a larger project, and it is a chance to correct old problems such as an undersized flue or framing that sits too close to the masonry.
Crown, matching brick and permits in a chimney rebuild
The new crown is cast to slope away from the flue, with an overhang and a drip edge so water falls clear of the brick below. A separate metal cap then covers the flue opening. We match the new brick to the old for size, color and texture, using reclaimed brick when the original is no longer made. Larger rebuilds can need a construction permit under the New Jersey Uniform Construction Code, so that is settled before work starts.

What affects the cost of a rebuild
- How many courses come down, and whether it is a partial or full rebuild.
- The number of flues and whether new liners are part of the job.
- The brick chosen and how hard the existing brick is to match.
- Roof access, scaffolding and any permit the work needs.
We give a written price once we have seen the chimney.
Why a loose chimney is a safety issue
Loose brick at the top of a chimney can fall onto the roof, a walkway or a car below, especially in high wind. A badly damaged chimney can also let heat and sparks reach the framing around it. Until it is rebuilt, it is safer not to use the fireplace or stove it serves.
Chimney rebuild questions
How do I know if my chimney needs a rebuild or just repair?
If the bricks are tight and the problem is worn mortar or a few damaged faces, repair is enough. Loose, leaning or crumbling brick across several courses usually means a rebuild.
Can a rebuilt chimney match the rest of my house?
Usually it can. We compare new and reclaimed brick to the existing chimney for color, size and texture, and match the mortar joint style so the new section blends in.
Does a chimney rebuild include a new crown and flashing?
Yes. Once the brick at the top and the roof line is relaid, the crown has to be cast new and the flashing has to be replaced to seal against the new masonry.
Can I use my fireplace while I wait for a rebuild?
It is safer not to. A chimney with loose brick or a damaged flue can let heat reach the house framing, so hold off until the work is done.
Our other services
Areas we serve
We bring this service to Bloomfield and every town below.
Find out if your chimney needs a rebuild
Send a photo of the top of the chimney or call (973) 786-9077. We will tell you how far down the damage goes.
